• - Thrust Restraint Design for Ductile Iron Pipe Seventh Edition
    thrust blocks when one leg is not horizontal; 2) the addition of well-graded ... (Fs)b, and Rs), and Appendix B (restrained joint design tables for horizontal bends).
  • - C-27 Thrust Restraint Design for Buried Piping
    Design the thrust blocks for lower vertical bends such that the contact pressure at the bottom of the block is within the allowable soil bearing capacity. e. Design ...
  • - STANDARD DETAILS
    CAST THE THRUST AREA OF ALL THRUST BLOCKS AGAINST A CLEAN FACE OF ... FOR DOWNWARD VERTICAL THRUST, THE ALLOWABLE BEARING ...
  • - watermain thrust block details - Armidale Regional Council
    TO BEND THRUST BLOCK. BEARING ... 110.23. THRUST BLOCK TABLE ... CONVEX VERTICAL BEND ANCHOR BLOCK TABLE. BLOCK.
  • - Vertical Thrust Blocking Standard Details - City of Lewisville
    A. VERT. BEND. UNDISTURBED EARTH. VERTICAL BLOCKING. FOR 11 1/4 , 22 1/2 & 30 BENDS. VERTICAL BLOCKING. FOR 45 & 90 BENDS. 1.0. L. (FT). D.
  • - vertical thrust block detail - Alberta Infrastructure
    NOTES: A. MAINTAIN CLEARANCE OF 80 mm FROM FACE. OF BELL TO CONCRETE. B. USE POLYETHYLENE BOND BREAKER ...
  • - S2015A MSC Thrust Block Details
    FSL MONTE. VERTICAL BENDS, SAG CONCRETE VOLUMES TO COUNTER THRUST. Thrust area. (m 3 PER 1200KPa TEST PRESSURE).
  • - Standard Drawing - Townsville City Council
    Thrust in both directions. Use puddle flange. Pipe length to suit. (See note 6). MINIMUM BLOCK VOLUME FOR ANCHORAGE. OF VERTICAL COMPONENT OF ...
  • - Drawing 50602 - Water Main Trust Block Details - Logan City Council
    For horizontal thrusts, the safe bearing load values for soils in trenches, where the cover over pipes is 450mm or greater. -Flanged sluice valve. - Thrust block.
  • - Engineering and Design: Revision of Thrust Block Criteria in ... - DTIC
    thrust block calculations until the criteria is incorporated into the applicable manual ... Thrust Blocks for Horizontal Bends. Refer to paragraph C- ...
  • - Untitled - Queensland Urban Utilities
    WHERE SKEW FITTINGS ARE APPROVED THE ANCHOR BLOCK ...... FOR DOWNWARD VERTICAL THRUST, THE ALLOWABLE BEARING PRESSURES ...
  • - Thrust Restraint - PA-AWWA
    Thrust Restraint Design for Ductile Iron PIpe. Design of Ductile ... Bearing. Gravity. Bearing Thrust Block .... begin deflect. Horizontal Bend / Vertical Up Bend. PA.
  • - TG 96 - SA Water
    NTS ON ANCHOR AND THRUST BLOCK LOCATION . .... ble Horizontal Bearing Pressures for Anchors and Thrust Blocks. nchorage on ...
  • - 5000-3 VERTICAL BEND THRUST BLOCK TABLE Model (1)
    KEEP CONCRETE CLEAR OF JOINT AND ACCESSORIES. INSTALL IN. ACCORDANCE TO TECHNICAL SPEC. SECTION 5000. 2. THRUST BLOCKS FOR ...
  • - drawing no. wsd 0140-b - 水務署
    TYPICAL BURIED THRUST BLOCK ... SCHEDULES OF TOP VERTICAL BEND. FOR DN450 .... SCHEDULES OF BOTTOM VERTICAL BEND.
  • - concrete thrust blocking - Municode
    5.0. THRU. VERTICAL DOW N BEND. THRU. 3.0 ... UPW ARD THRUST GRAVITY BLOCKS. NOTE 2 ... PRESSURE. THRUST BLOCK DESIGN AS FOLLOW S.
  • - thrust blocking standards - Beaverton, OR
    (BEARING AREA OF THRUST BLOCKS IN SQUARE FEET). 21.7. 28.4 ... Vertical changes in direction require specific designs for thrust blocks. BEND. TEE.
  • - thrust blocks for water lines - Town of Pittsboro
    3. FORM ALL NON-BEARING VERTICAL SURFACES. 4. THRUST BLOCKS ARE TO EXTEND TO. UNDISTURBED GROUND. CONCRETE TO BE. CLASS 'C'.
  • - state of new york department of transportation vertical thrust ... - nysdot
    NUMBERS IN PARENTHESIS ARE BAR SIZES MARKED IN EIGHTHS OF INCHES. ANCHOR ROD SCHEDULE FOR GRAVITY BLOCKS. THRUST ...
  • - thrust blocking - ODOT FTP
    VERTICAL BEND. CONVEX. WYE. THRUST BLOCKING. TABLE A. TABLE C. 48740. 37320. 27405. 19045. 12185. 6860. 3035. 69245. 53010.
  • - SD 610 — Concrete Thrust Blocks
    The use of Portland cement concrete thrust blocks is not permissible except as shown ... or greater than the vertical component of thrust on the vertical bend. 3.
  • - Untitled
    The use of Portland cement concrete thrust blocks is not permissible except as shown on ... or greater than the vertical component of thrust on the vertical bend.
  • - W-09 Vertical Thrust Block Detail - Town of Batavia
    NOTE: THE DEVELOPER MAY ELECT TO USE REINFORCING RODS AS OPPOSED TO CONCRETE THRUST BLOCKS FOR. VERTICAL BENDS.
  • - 312-0 Thrust Block and Restraint - City of Brea
    THRUST BLOCK. VERTICAL BEND. NOTES: 1. ALL FITTING OR PIPE JOINTS WITHIN LENGTH INDICATED ON SHEET 3 SHALL. BE FULLY RESTRAINED. 2.
  • - WL-407 Vertical Thrust Blocking - City of West Linn
    GRAVITY VERTICAL THRUST BLOCKS SHALL BE DESIGNED BY THE ENGINEER. 2. KEEP CONCRETE CLEAR OF JOINT AND JOINT ACCESSORIES.
  • - thrust block at capped ends thrust blocks on horizontal thrust block at ...
    THRUST BLOCKS ON HORIZONTAL. THRUST BLOCK AT REDUCER. ELEVATION. DIAMETER. THRUST BLOCKS ON VERTICAL BENDS. NOTE:- 150. 100.
  • - T-1103.020 Concrete Thrust Blocks for Vertical Bends
    DOWN-THRUST BLOCK. NOTES: 1. CONCRETE SHALL BE PLACED TO WITHIN. 50 mm OF THE FACE OF THE BELL. 2. POLYETHYLENE BOND BREAKER ...
  • - Thrust Block Details - Boston Water and Sewer Commission
    UNREINFORCED THRUST BLOCK SHOWN .... Enter Table I at 24-inch pipe diameter - go vertically down column until opposite 67-1/2° angle.
  • - Thrust Blocking - Tyler Public Works
    HATI HIB. THRUST SUPPORT FOR REDUCER. BLOCKING FOR. BLOCKING FOR VERTICAL BENDS. (Sizes to be Determined by Engineer.
  • - Horizontal Thrust Block - At Pipe Bends - City of Wichita Falls
    CONCRETE PIPE. 3. VOLUMES OF 'THRUST BLOCKS ARE NET VOLUMES OF. CONCRETE TO BE FURNISHED. THE CORRESPONDING WEIGHT. OF 'THE ...


  • © 2018 PDFPit.com. All right reserved. Contact Us: PDFPit[at]outlook.com